Spacelog Apollo 13

Okay. I've got it, Joe.

Okay, now -

Okay. Now we've got to make the belt real taut here.

How's that?

Okay, Joe.

Okay, Jack. Did you have —

— Hey, Houston, are you reading?

Jack —

— We've got the two belts around the top and the one around the bottom all done.

Okay, fine. The next step now is to anchor that tape, and the way we want you to do that is to cut about a 2-foot length off the roll and then tear it lengthwise so that you have two strips about 2 feet long and about a half an inch wide. And you'll wrap those around the canister at right angles, more or less, to the tape that you've got so that it goes across the top and across the bottom; and when it goes across the top and the bottom, put it so that it's outboard of the center hole and try to get it over one of the ridges between the screens, so that it won't block the flow. Is that clear? Over.

Yes, Joe. Very good.

Okay. Press on.

Okay. I've got a cut length right here and we'll tear it lengthwise … and I'm going to go around right here at this ridge all the way around at right angles and anchor it …

Yes.

Joe, just to clarify that, sticky end down. Right? On the tape that I am putting on now?

I didn't quite copy that, Jack. Say again.

Okay. That will be the sticky end down on the container, right?

Oh, that's correct. I forgot to say that. That's right.

… hold that one right here, if I can set it.

Okay, Joe; Aquarius. We've got that done.

Okay, Jack. The next step is to get the EVA cue card and use it to form an arch over the top of the canister; just tuck one short end under one ridge on the top the other one against the ridge on the other side so that it forms a rounded arch over the top of the canister. You see, Jack, what we're going to do is slip the bag over this whole assembly and the cue card will serve to keep the bag from being sucked down against the screen. Over.

Okay. I got the idea.

Okay. And when you've done that, to hold the arch in place, just run a strip of tape across the side of the—that is, across the top of the arch, and anchor it down to the sticky strips along each side.

Okay. I got the idea. Okay. Let me just repeat it here. Take a cue card, form an arch over the top, bringing it under the side here. When we're through, run a piece of tape from the sides across the top of that to anchor to the other side.

That's correct.

Okay. It worked.

The top. … Across the top.

Looks like you're going to have to cut the cue card slightly.

Doesn't have to be really … over that the only thing we're … we can just take the scissors and cut off the edge here. The only thing this does, Jim, is prevent this from being sucked down into the container.

Okay, Joe. We've got that arch built, and it's all taped in securely.

Okay, Jack. The next step is to stop up the bypass hole, which is the hole in the center of the bottom of the canister; we want to stop that up because we don't want to bypass the flow; and I forgot to tell you to get something to stick in that hole. We recommend that you either use a wetwipe, or cut off a piece of sock and stuff it in there, or you could probably even crumble up some tape and use that. Over.

Okay. We'll start plugging up the bypass hole.

Okay.

Plug that hole. We can either—we can put some either—Let's cut a piece of your towel there.

Okay.

Okay. Now, Joe, you want to cut four strips, 12 inches long each, 1/2-inch in diameter. Tape that along the outsides of the bag across the ribs.

Okay, Houston; Aquarius. We've got the four strips in place.

Okay. We're in business now with the bag, and the next step to perform is to get ready to put the red suit hose, either the commander's or the LMP's because we're—we're going to want you to have both of these made up eventually, into the top of the—of the bag, and to do that you, first of all, have to assure that the—that the red hose is separated from the blue hose. I don't know whether this has been done already, but if it hasn't, what you have to do is cut the outer Beta-cloth sheath down the full length of the—of the hoses and then also cut the rubber ties that secure the two hoses together, and the hoses should come apart and the COMM cable should—should come off. Over.

Okay. Take the —I'm going to want to separate the red hose from the blue hose by cutting this Beta-cloth sheath. Okay. That's in work.

Okay.

Okay, Houston; Aquarius. I have the LMP's red hose separated from the others.

Okay. Real fine. Now the next step is to cut a diagonal hole in one ear of the—of the plastic bag near the arch. You can pick either one and cut about, a 1-1/2 or 2 inch diagonal hole, big enough to slip the red hose through. And when you've done that, you'll just slip the red hose through so that it goes about to the center of the canister. It's—it's—It's not critical except that the opening should be down, and then tape the bag to the hose where it goes in so that it's nice and snug. Over.

Okay. Copy that. We want a 1-1/2 inch hole right here at this ear, and put the hose in here, end down and toward the canister and then we tape the seal around here.

Let's try it. We can always make it bigger if we have to. Fred, get those. … the center of the arch.

Okay, Jack. Now the remaining steps are simply suit-loop configuration steps to get this thing into full operation, and our ECS people want to hold off on that until the canister you're working on gets to 7.6 millimeters of mercury, which will probably be another 45 minutes or an hour—it—We're reading 4.7 now. So what we'd like you to do in the interim is to set up the second command module canister the same way you just did the first one, using the commander's hose, and get that all set and probably about that time it'll be time to—to switch over. For your information, when you've got that done and if you've had your breakfast and so on, the next thing I've got for you is a switch-configuration list for the command module, which will represent the—the powerdown, square-1 starting configuration for all our—our preentry checks. Over.

Okay. We'll start setting up the commander's hose configuration the same as the LMP's hose. And I'll get—instead of—I guess you want me to use my launch …—launch checklist which I'd …

That's affirmative, Jack. What we have done is marked up the lift-off configuration checklist, and we'll run through it whenever you get around to it.

And, I assume that …

What I'd better do is before I put this thing back in operation, they're going to complete that other canister. I don't know. It should be in operation now. …

Okay, Houston; Aquarius.

Aquarius, Houston. Go.

Okay, Joe. Should this canister be in operation now because it's already mounted on the hose?

Well, yes. We haven't completely configured the suit loop to get full flow through there, and it's okay the way it is. What I recommend you do with the commander's hose is get the bag all ready, but not stick the hose in until we call you on it. Okay.

Okay. Will do.

It won't go around?

Yes. Or else a strip of tape.

Okay, Jim. We've got to start setting up the commander's. …

Yes. … show. How about that … because I've got two in my …

Yes. Here, we'll store them back where I got it.

Hello, Aquarius; Houston.

Go ahead.

Roger, Jack; Tom here. Just thought I would pass on to you and Jim that got a little data priority going today, and going to convene to CPCB and we'll have you all kinds of good procedures for later on. Over.

Okay. Thank you, Tom. You guys are really working overtime.

We're getting a little coordination down here.

Aquarius, Houston. You might pass on to Jim, he had such a long day yesterday, we thought we were going to have to play him some guitar music to get him to sleep last night. Over.

That's exactly what he did. Tom said you had such a long day yesterday, he thought he was going to have to play some guitar music to get you to sleep.

Tom said the CPCB is getting …