Apollo 13 transcript starting at 05 06 16 42 on Spacelog

Load previous…

05 06 16 42
Ken Mattingly: Okay. That's the panel 8 floodlights. Now we're going to take panel 5 and put the FLOODLIGHT rheostat to FLOOD and the LEB, that's panel 100, FLOODLIGHTS are also going to FIXED. And the purpose of this is to balance up buses A and B.
05 06 17 05
Jack Swigert (CMP): Okay. Panel 5; FLOODLIGHTS; you want the rheostat on. Panel 100, FLOODLIGHTS; you want FIXED.
05 06 17 14
Ken Mattingly: That's affirmative. Okay. On panel 8: circuit breakers EMS, MAIN A and MAIN B, that's two, open.
05 06 17 47
Jack Swigert (CMP): Okay. Panel 8: EMS MAIN A and MAIN B, open.
05 06 17 51
Ken Mattingly: Okay. On panel 250: circuit breaker BATTERY A POWER ENTRY and POSTLANDING, closed.
05 06 18 14
Jack Swigert (CMP): Okay. Panel 250: CB BAT A POWER ENTRY and POSTLANDING, closed.
05 06 18 20
Ken Mattingly: Okay. The same for circuit breaker BATTERY B POWER ENTRY and POSTLANDING.
05 06 18 39
Jack Swigert (CMP): Okay. BATTERY B POWER ENTRY and POSTLANDING, closed.
05 06 18 42
Ken Mattingly: Okay. And add BATTERY C POWER ENTRY and POSTLANDING.
05 06 19 00
Jack Swigert (CMP): BATTERY C POWER ENTRY and POSTLANDING, closed.
05 06 19 03
Ken Mattingly: Okay. That's correct. On panel 5: circuit breaker BAT CHARGE, BATTERY A CHARGE, closed.
05 06 19 27
Jack Swigert (CMP): Okay. Panel 5: CB BAT CHARGE, BAT A, close.
05 06 19 32
Ken Mattingly: Okay. And the same for circuit breaker for BATTERY CHARGE, BAT B/CHARGE, closed.
05 06 19 52
Jack Swigert (CMP): Okay, BAT CHARGER, BAT B, closed.
05 06 19 56
Ken Mattingly: All right. Like to take MAIN BUS TIES, two of them, on and up. That's probably a verify.
05 06 20 16
Jack Swigert (CMP): MAIN BUS TIES A/C and B/C, on, verify.
05 06 20 21
Ken Mattingly: That's correct. Circuit breaker BATTERY RELAY BUS, BATTERY A and B, closed.
05 06 20 43
Jack Swigert (CMP): Okay. CB BAT RELAY BUS, BAT A, and BAT RELAY BUS, BAT B, closed.
Expand selection up Contract selection down Close
05 06 20 49
Ken Mattingly: That's affirmative. Circuit breaker EPS SENSOR SIGNAL, MAIN A and MAIN B, closed.
05 06 21 13
Jack Swigert (CMP): EPS SENSOR SIGNAL, MAIN A and MAIN B, closed.
05 06 21 18
Ken Mattingly: Okay. On panel 275: circuit breaker MAIN A, BATTERY C, closed.
05 06 21 37
Jack Swigert (CMP): Okay, Ken. Wait on that one here. I'm just about to lose you here. Just—I've got to change OMNIs.
05 06 21 42
Ken Mattingly: Okay.
05 06 21 47
Jack Swigert (CMP): Okay. Could you give me that one again, please.
05 06 21 50
Ken Mattingly: All right. On panel 275: circuit breaker MAIN A, BATTERY C, closed.
05 06 22 05
Jack Swigert (CMP): Okay. MAIN A, BAT B, closed on 275.
05 06 22 09
Ken Mattingly: That's MAIN A, BATTERY C, Charlie.
05 06 22 15
Jack Swigert (CMP): MAIN A, BAT C, Charlie.
05 06 22 20
Ken Mattingly: That's affirm. No—Negative on battery Bravo.
05 06 22 27
Jack Swigert (CMP): Okay. Negative on battery Bravo. That's MAIN A, BAT Charlie, closed.
05 06 22 32
Ken Mattingly: Okay. Good. On panel 276: circuit breaker INSTRUMENTATION POWER CONTROL, 3 and 4, open.
05 06 22 49
Jack Swigert (CMP): Would you say that one again, Ken?
05 06 22 51
Ken Mattingly: All right. On panel 276: circuit breaker INSTRUMENTATION POWER CONTROL, 3 and 4, open.
05 06 23 17
Jack Swigert (CMP): Okay. Panel 276: CB INSTRUMENTATION POWER CONTROL, 3 and 4, open.
Expand selection down Contract selection up
05 06 23 24
Ken Mattingly: That's affirmative. Okay. Panel 5: circuit breaker CENTRAL INSTRUMENTATION POWER, MAIN B, closed.
05 06 23 51
Jack Swigert (CMP): Okay. On panel 5: …
05 06 23 59
Ken Mattingly: Okay. I'm sorry, Jack. Would you read that again, please?
05 06 24 03
Jack Swigert (CMP): Okay. On panel 5: CB CENTRAL INSTRUMENTATION POWER, MAIN B, closed.
05 06 24 10
Ken Mattingly: Okay. That's correct. PRIMARY EVAPORATE WATER CONTROL valve to AUTO.
05 06 24 24
Jack Swigert (CMP): This is on 382?
05 06 24 27
Ken Mattingly: That's affirmative.
05 06 24 28
Jack Swigert (CMP): Wha—Wha -
05 06 24 30
Ken Mattingly: Okay, Jack. We want to put the PRIMARY and the SECONDARY EVAPORATED WATER CONTROL valves to AUTO.
05 06 24 37
Jack Swigert (CMP): Okay.
05 06 24 52
Ken Mattingly: And, Jack, can you give us a readout on BAT B and the charger current?
05 06 25 14
Jack Swigert (CMP): Okay, Ken. That was the PRIMARY and SECONDARY H₂O CONTROL valves to AUTO on 382.
05 06 25 20
Ken Mattingly: That's affirmative, and did you copy about the readout on the battery and charger?
05 06 25 25
Jack Swigert (CMP): Yes. Jim's on his way up.
05 06 25 27
Ken Mattingly: Okay. Thank you. All right, the next little step after your water control valves is to perform the CSM RCS preheat. We'll do that on page E/1-5, steps 35 and 37.
05 06 25 53
Jack Swigert (CMP): Okay, Ken. We're having a problem with the COMM. You read now?

Spacelog Apollo 13